diff --git a/main/CMakeLists.txt b/main/CMakeLists.txt
index a832818fd..d6d840e3e 100644
--- a/main/CMakeLists.txt
+++ b/main/CMakeLists.txt
@@ -141,6 +141,10 @@ elseif(CONFIG_BOARD_TYPE_MIXGO_NOVA)
set(BOARD_TYPE "mixgo-nova")
elseif(CONFIG_BOARD_TYPE_ESP32_CGC)
set(BOARD_TYPE "esp32-cgc")
+elseif(CONFIG_BOARD_TYPE_MINSI_K08_WIFI)
+ set(BOARD_TYPE "minsi-k08-wifi")
+elseif(CONFIG_BOARD_TYPE_MINSI_K08_ML307)
+ set(BOARD_TYPE "minsi-k08-ml307")
endif()
file(GLOB BOARD_SOURCES
${CMAKE_CURRENT_SOURCE_DIR}/boards/${BOARD_TYPE}/*.cc
diff --git a/main/Kconfig.projbuild b/main/Kconfig.projbuild
index 631cde6b8..2ac8a6a48 100644
--- a/main/Kconfig.projbuild
+++ b/main/Kconfig.projbuild
@@ -162,6 +162,10 @@ choice BOARD_TYPE
bool "四博智联AI陪伴盒子"
config BOARD_TYPE_MIXGO_NOVA
bool "元控·青春"
+ config BOARD_TYPE_MINSI_K08_WIFI
+ bool "敏思科技K08(WIFI)"
+ config BOARD_TYPE_MINSI_K08_ML307
+ bool "敏思科技K08(ML307)"
endchoice
choice DISPLAY_OLED_TYPE
diff --git a/main/boards/minsi-k08-ml307/README.md b/main/boards/minsi-k08-ml307/README.md
new file mode 100644
index 000000000..d70521057
--- /dev/null
+++ b/main/boards/minsi-k08-ml307/README.md
@@ -0,0 +1,36 @@
+
+minsi-k08-wifi和minsi-k08-ml307是敏思科技推出的基于ESP32S3N16R8，搭载MAX98357音频功率放大器和INMP441全向麦克风模块，通过改造K08透明机甲小钢炮音箱而成的带有朋克风格的大喇叭大电池小智AI聊天机器人方案。
+
+Minsi-k08
+
+
+ 
+
+
+
+
+# 编译配置命令
+
+**配置编译目标为 ESP32S3：**
+
+```bash
+idf.py set-target esp32s3
+```
+
+**打开 menuconfig：**
+
+```bash
+idf.py menuconfig
+```
+
+**选择板子：**
+
+```
+Xiaozhi Assistant -> Board Type ->敏思科技K08(ML307)
+```
+
+**编译烧入：**
+
+```bash
+idf.py build flash
+```
\ No newline at end of file
diff --git a/main/boards/minsi-k08-ml307/config.h b/main/boards/minsi-k08-ml307/config.h
new file mode 100644
index 000000000..8529c173e
--- /dev/null
+++ b/main/boards/minsi-k08-ml307/config.h
@@ -0,0 +1,73 @@
+#ifndef _BOARD_CONFIG_H_
+#define _BOARD_CONFIG_H_
+
+#include
+
+#define AUDIO_INPUT_SAMPLE_RATE 16000
+#define AUDIO_OUTPUT_SAMPLE_RATE 24000
+
+// 如果使用 Duplex I2S 模式，请注释下面一行
+#define AUDIO_I2S_METHOD_SIMPLEX
+
+#ifdef AUDIO_I2S_METHOD_SIMPLEX
+
+//#define AUDIO_I2S_MIC_GPIO_WS GPIO_NUM_4
+//#define AUDIO_I2S_MIC_GPIO_SCK GPIO_NUM_5
+//#define AUDIO_I2S_MIC_GPIO_DIN GPIO_NUM_6
+//#define AUDIO_I2S_SPK_GPIO_DOUT GPIO_NUM_7
+//#define AUDIO_I2S_SPK_GPIO_BCLK GPIO_NUM_15
+//#define AUDIO_I2S_SPK_GPIO_LRCK GPIO_NUM_16
+
+#define AUDIO_I2S_MIC_GPIO_WS GPIO_NUM_9
+#define AUDIO_I2S_MIC_GPIO_SCK GPIO_NUM_10
+#define AUDIO_I2S_MIC_GPIO_DIN GPIO_NUM_18
+#define AUDIO_I2S_SPK_GPIO_DOUT GPIO_NUM_4
+#define AUDIO_I2S_SPK_GPIO_BCLK GPIO_NUM_5
+#define AUDIO_I2S_SPK_GPIO_LRCK GPIO_NUM_6
+#else
+
+#define AUDIO_I2S_GPIO_WS GPIO_NUM_4
+#define AUDIO_I2S_GPIO_BCLK GPIO_NUM_5
+#define AUDIO_I2S_GPIO_DIN GPIO_NUM_6
+#define AUDIO_I2S_GPIO_DOUT GPIO_NUM_7
+
+#endif
+
+//#define BUILTIN_LED_GPIO GPIO_NUM_48
+//#define BOOT_BUTTON_GPIO GPIO_NUM_0
+//#define TOUCH_BUTTON_GPIO GPIO_NUM_47
+//#define VOLUME_UP_BUTTON_GPIO GPIO_NUM_40
+//#define VOLUME_DOWN_BUTTON_GPIO GPIO_NUM_39
+#define BUILTIN_LED_GPIO GPIO_NUM_40
+#define BOOT_BUTTON_GPIO GPIO_NUM_0
+#define TOUCH_BUTTON_GPIO GPIO_NUM_NC
+#define VOLUME_UP_BUTTON_GPIO GPIO_NUM_NC
+#define VOLUME_DOWN_BUTTON_GPIO GPIO_NUM_NC
+
+#define DISPLAY_BACKLIGHT_PIN GPIO_NUM_7
+#define DISPLAY_MOSI_PIN GPIO_NUM_17
+#define DISPLAY_CLK_PIN GPIO_NUM_8
+#define DISPLAY_DC_PIN GPIO_NUM_15
+#define DISPLAY_RST_PIN GPIO_NUM_16
+#define DISPLAY_CS_PIN GPIO_NUM_NC
+
+
+//#define ML307_RX_PIN GPIO_NUM_38
+//#define ML307_TX_PIN GPIO_NUM_39
+//#define ML307_RX_PIN GPIO_NUM_39
+//#define ML307_TX_PIN GPIO_NUM_38
+#define ML307_RX_PIN GPIO_NUM_11
+#define ML307_TX_PIN GPIO_NUM_12
+
+#define DISPLAY_WIDTH 240
+#define DISPLAY_HEIGHT 240
+#define DISPLAY_MIRROR_X false
+#define DISPLAY_MIRROR_Y true
+#define DISPLAY_SWAP_XY true
+#define DISPLAY_INVERT_COLOR true
+#define DISPLAY_RGB_ORDER LCD_RGB_ELEMENT_ORDER_RGB
+#define DISPLAY_OFFSET_X 80
+#define DISPLAY_OFFSET_Y 0
+#define DISPLAY_BACKLIGHT_OUTPUT_INVERT false
+
+#endif // _BOARD_CONFIG_H_
diff --git a/main/boards/minsi-k08-ml307/config.json b/main/boards/minsi-k08-ml307/config.json
new file mode 100644
index 000000000..753c9ed2e
--- /dev/null
+++ b/main/boards/minsi-k08-ml307/config.json
@@ -0,0 +1,9 @@
+{
+ "target": "esp32s3",
+ "builds": [
+ {
+ "name": "minsi-k08-ml307",
+ "sdkconfig_append": []
+ }
+ ]
+}
\ No newline at end of file
diff --git a/main/boards/minsi-k08-ml307/minsi_k08_ml307.cc b/main/boards/minsi-k08-ml307/minsi_k08_ml307.cc
new file mode 100644
index 000000000..6a2f5acaa
--- /dev/null
+++ b/main/boards/minsi-k08-ml307/minsi_k08_ml307.cc
@@ -0,0 +1,143 @@
+#include "ml307_board.h"
+//#include "wifi_board.h"
+#include "audio_codecs/no_audio_codec.h"
+#include "display/lcd_display.h"
+#include "system_reset.h"
+#include "application.h"
+#include "button.h"
+#include "config.h"
+#include "iot/thing_manager.h"
+#include "led/single_led.h"
+#include "assets/lang_config.h"
+
+//#include
+#include
+#include
+#include
+#include
+#include
+#include
+
+#define TAG "MINSI_K08_ML307"
+
+LV_FONT_DECLARE(font_puhui_16_4);
+LV_FONT_DECLARE(font_awesome_16_4);
+
+class MINSI_K08_ML307 : public Ml307Board {
+private:
+
+ Button boot_button_;
+ LcdDisplay* display_;
+
+ void InitializeSpi() {
+ spi_bus_config_t buscfg = {};
+ buscfg.mosi_io_num = DISPLAY_MOSI_PIN;
+ buscfg.miso_io_num = GPIO_NUM_NC;
+ buscfg.sclk_io_num = DISPLAY_CLK_PIN;
+ buscfg.quadwp_io_num = GPIO_NUM_NC;
+ buscfg.quadhd_io_num = GPIO_NUM_NC;
+ buscfg.max_transfer_sz = DISPLAY_WIDTH * DISPLAY_HEIGHT * sizeof(uint16_t);
+ ESP_ERROR_CHECK(spi_bus_initialize(SPI3_HOST, &buscfg, SPI_DMA_CH_AUTO));
+ }
+
+ void InitializeLcdDisplay() {
+ esp_lcd_panel_io_handle_t panel_io = nullptr;
+ esp_lcd_panel_handle_t panel = nullptr;
+ // 液晶屏控制IO初始化
+ ESP_LOGD(TAG, "Install panel IO");
+ esp_lcd_panel_io_spi_config_t io_config = {};
+ io_config.cs_gpio_num = DISPLAY_CS_PIN;
+ io_config.dc_gpio_num = DISPLAY_DC_PIN;
+ io_config.spi_mode = 3;
+ io_config.pclk_hz = 40 * 1000 * 1000;
+ io_config.trans_queue_depth = 10;
+ io_config.lcd_cmd_bits = 8;
+ io_config.lcd_param_bits = 8;
+ ESP_ERROR_CHECK(esp_lcd_new_panel_io_spi(SPI3_HOST, &io_config, &panel_io));
+
+ // 初始化液晶屏驱动芯片
+ ESP_LOGD(TAG, "Install LCD driver");
+ esp_lcd_panel_dev_config_t panel_config = {};
+ panel_config.reset_gpio_num = DISPLAY_RST_PIN;
+ panel_config.rgb_ele_order = DISPLAY_RGB_ORDER;
+ panel_config.bits_per_pixel = 16;
+
+ ESP_ERROR_CHECK(esp_lcd_new_panel_st7789(panel_io, &panel_config, &panel));
+
+ esp_lcd_panel_reset(panel);
+
+
+ esp_lcd_panel_init(panel);
+ esp_lcd_panel_invert_color(panel, DISPLAY_INVERT_COLOR);
+ esp_lcd_panel_swap_xy(panel, DISPLAY_SWAP_XY);
+ esp_lcd_panel_mirror(panel, DISPLAY_MIRROR_X, DISPLAY_MIRROR_Y);
+
+ display_ = new SpiLcdDisplay(panel_io, panel,
+ DISPLAY_WIDTH, DISPLAY_HEIGHT, DISPLAY_OFFSET_X, DISPLAY_OFFSET_Y, DISPLAY_MIRROR_X, DISPLAY_MIRROR_Y, DISPLAY_SWAP_XY,
+ {
+ .text_font = &font_puhui_16_4,
+ .icon_font = &font_awesome_16_4,
+ .emoji_font = DISPLAY_HEIGHT >= 240 ? font_emoji_64_init() : font_emoji_32_init(),
+ });
+ }
+
+ void InitializeButtons() {
+ boot_button_.OnClick([this]() {
+ Application::GetInstance().ToggleChatState();
+ });
+ }
+
+ // 物联网初始化，添加对 AI 可见设备
+ void InitializeIot() {
+ auto& thing_manager = iot::ThingManager::GetInstance();
+ thing_manager.AddThing(iot::CreateThing("Speaker"));
+ thing_manager.AddThing(iot::CreateThing("Lamp"));
+ if (DISPLAY_BACKLIGHT_PIN != GPIO_NUM_NC) {
+ thing_manager.AddThing(iot::CreateThing("Backlight"));
+ }
+ }
+
+
+public:
+ MINSI_K08_ML307() : Ml307Board(ML307_TX_PIN, ML307_RX_PIN, 4096),
+ boot_button_(BOOT_BUTTON_GPIO) {
+
+ InitializeSpi();
+ InitializeLcdDisplay();
+ InitializeButtons();
+ InitializeIot();
+ if (DISPLAY_BACKLIGHT_PIN != GPIO_NUM_NC) {
+ GetBacklight()->RestoreBrightness();
+ }
+ }
+
+ virtual Led* GetLed() override {
+ static SingleLed led(BUILTIN_LED_GPIO);
+ return &led;
+ }
+
+ virtual AudioCodec* GetAudioCodec() override {
+#ifdef AUDIO_I2S_METHOD_SIMPLEX
+ static NoAudioCodecSimplex audio_codec(AUDIO_INPUT_SAMPLE_RATE, AUDIO_OUTPUT_SAMPLE_RATE,
+ AUDIO_I2S_SPK_GPIO_BCLK, AUDIO_I2S_SPK_GPIO_LRCK, AUDIO_I2S_SPK_GPIO_DOUT, AUDIO_I2S_MIC_GPIO_SCK, AUDIO_I2S_MIC_GPIO_WS, AUDIO_I2S_MIC_GPIO_DIN);
+#else
+ static NoAudioCodecDuplex audio_codec(AUDIO_INPUT_SAMPLE_RATE, AUDIO_OUTPUT_SAMPLE_RATE,
+ AUDIO_I2S_GPIO_BCLK, AUDIO_I2S_GPIO_WS, AUDIO_I2S_GPIO_DOUT, AUDIO_I2S_GPIO_DIN);
+#endif
+ return &audio_codec;
+ }
+
+ virtual Display* GetDisplay() override {
+ return display_;
+ }
+
+ virtual Backlight* GetBacklight() override {
+ if (DISPLAY_BACKLIGHT_PIN != GPIO_NUM_NC) {
+ static PwmBacklight backlight(DISPLAY_BACKLIGHT_PIN, DISPLAY_BACKLIGHT_OUTPUT_INVERT);
+ return &backlight;
+ }
+ return nullptr;
+ }
+};
+
+DECLARE_BOARD(MINSI_K08_ML307);
diff --git a/main/boards/minsi-k08-wifi/README.md b/main/boards/minsi-k08-wifi/README.md
new file mode 100644
index 000000000..aed0e147d
--- /dev/null
+++ b/main/boards/minsi-k08-wifi/README.md
@@ -0,0 +1,36 @@
+
+minsi-k08-wifi和minsi-k08-ml307是敏思科技推出的基于ESP32S3N16R8，搭载MAX98357音频功率放大器和INMP441全向麦克风模块，通过改造K08透明机甲小钢炮音箱而成的带有朋克风格的大喇叭大电池小智AI聊天机器人方案。
+
+Minsi-k08
+
+
+ 
+
+
+
+
+# 编译配置命令
+
+**配置编译目标为 ESP32S3：**
+
+```bash
+idf.py set-target esp32s3
+```
+
+**打开 menuconfig：**
+
+```bash
+idf.py menuconfig
+```
+
+**选择板子：**
+
+```
+Xiaozhi Assistant -> Board Type ->敏思科技K08(WIFI)
+```
+
+**编译烧入：**
+
+```bash
+idf.py build flash
+```
\ No newline at end of file
diff --git a/main/boards/minsi-k08-wifi/config.h b/main/boards/minsi-k08-wifi/config.h
new file mode 100644
index 000000000..b159f8a99
--- /dev/null
+++ b/main/boards/minsi-k08-wifi/config.h
@@ -0,0 +1,68 @@
+#ifndef _BOARD_CONFIG_H_
+#define _BOARD_CONFIG_H_
+
+#include
+
+#define AUDIO_INPUT_SAMPLE_RATE 16000
+#define AUDIO_OUTPUT_SAMPLE_RATE 24000
+
+// 如果使用 Duplex I2S 模式，请注释下面一行
+#define AUDIO_I2S_METHOD_SIMPLEX
+
+#ifdef AUDIO_I2S_METHOD_SIMPLEX
+
+//#define AUDIO_I2S_MIC_GPIO_WS GPIO_NUM_4
+//#define AUDIO_I2S_MIC_GPIO_SCK GPIO_NUM_5
+//#define AUDIO_I2S_MIC_GPIO_DIN GPIO_NUM_6
+//#define AUDIO_I2S_SPK_GPIO_DOUT GPIO_NUM_7
+//#define AUDIO_I2S_SPK_GPIO_BCLK GPIO_NUM_15
+//#define AUDIO_I2S_SPK_GPIO_LRCK GPIO_NUM_16
+#define AUDIO_I2S_MIC_GPIO_WS GPIO_NUM_9
+#define AUDIO_I2S_MIC_GPIO_SCK GPIO_NUM_10
+#define AUDIO_I2S_MIC_GPIO_DIN GPIO_NUM_18
+#define AUDIO_I2S_SPK_GPIO_DOUT GPIO_NUM_4
+#define AUDIO_I2S_SPK_GPIO_BCLK GPIO_NUM_5
+#define AUDIO_I2S_SPK_GPIO_LRCK GPIO_NUM_6
+#else
+
+#define AUDIO_I2S_GPIO_WS GPIO_NUM_4
+#define AUDIO_I2S_GPIO_BCLK GPIO_NUM_5
+#define AUDIO_I2S_GPIO_DIN GPIO_NUM_6
+#define AUDIO_I2S_GPIO_DOUT GPIO_NUM_7
+
+#endif
+
+
+#define BUILTIN_LED_GPIO GPIO_NUM_40
+#define BOOT_BUTTON_GPIO GPIO_NUM_0
+#define TOUCH_BUTTON_GPIO GPIO_NUM_NC
+#define VOLUME_UP_BUTTON_GPIO GPIO_NUM_NC
+#define VOLUME_DOWN_BUTTON_GPIO GPIO_NUM_NC
+
+
+//#define DISPLAY_BACKLIGHT_PIN GPIO_NUM_42
+//#define DISPLAY_MOSI_PIN GPIO_NUM_47
+//#define DISPLAY_CLK_PIN GPIO_NUM_21
+//#define DISPLAY_DC_PIN GPIO_NUM_40
+//#define DISPLAY_RST_PIN GPIO_NUM_45
+//#define DISPLAY_CS_PIN GPIO_NUM_41
+#define DISPLAY_BACKLIGHT_PIN GPIO_NUM_7
+#define DISPLAY_MOSI_PIN GPIO_NUM_17
+#define DISPLAY_CLK_PIN GPIO_NUM_8
+#define DISPLAY_DC_PIN GPIO_NUM_15
+#define DISPLAY_RST_PIN GPIO_NUM_16
+#define DISPLAY_CS_PIN GPIO_NUM_NC
+
+#define DISPLAY_WIDTH 240
+#define DISPLAY_HEIGHT 240
+#define DISPLAY_MIRROR_X false
+#define DISPLAY_MIRROR_Y true
+#define DISPLAY_SWAP_XY true
+#define DISPLAY_INVERT_COLOR true
+#define DISPLAY_RGB_ORDER LCD_RGB_ELEMENT_ORDER_RGB
+#define DISPLAY_OFFSET_X 80
+#define DISPLAY_OFFSET_Y 0
+#define DISPLAY_BACKLIGHT_OUTPUT_INVERT false
+
+
+#endif // _BOARD_CONFIG_H_
diff --git a/main/boards/minsi-k08-wifi/config.json b/main/boards/minsi-k08-wifi/config.json
new file mode 100644
index 000000000..8592aba7c
--- /dev/null
+++ b/main/boards/minsi-k08-wifi/config.json
@@ -0,0 +1,9 @@
+{
+ "target": "esp32s3",
+ "builds": [
+ {
+ "name": "minsi-k08-wifi",
+ "sdkconfig_append": []
+ }
+ ]
+}
\ No newline at end of file
diff --git a/main/boards/minsi-k08-wifi/minsi-k08.jpg b/main/boards/minsi-k08-wifi/minsi-k08.jpg
new file mode 100644
index 000000000..1b48345fb
Binary files /dev/null and b/main/boards/minsi-k08-wifi/minsi-k08.jpg differ
diff --git a/main/boards/minsi-k08-wifi/minsi_k08_wifi.cc b/main/boards/minsi-k08-wifi/minsi_k08_wifi.cc
new file mode 100644
index 000000000..77aeeaedc
--- /dev/null
+++ b/main/boards/minsi-k08-wifi/minsi_k08_wifi.cc
@@ -0,0 +1,148 @@
+#include "wifi_board.h"
+#include "audio_codecs/no_audio_codec.h"
+#include "display/lcd_display.h"
+#include "system_reset.h"
+#include "application.h"
+#include "button.h"
+#include "config.h"
+#include "iot/thing_manager.h"
+#include "led/single_led.h"
+
+#include
+#include
+#include
+#include
+#include
+#include
+#include
+
+
+#define TAG "MINSI_K08_WIFI"
+
+LV_FONT_DECLARE(font_puhui_16_4);
+LV_FONT_DECLARE(font_awesome_16_4);
+
+class MINSI_K08_WIFI : public WifiBoard {
+private:
+
+ Button boot_button_;
+ LcdDisplay* display_;
+
+ void InitializeSpi() {
+ spi_bus_config_t buscfg = {};
+ buscfg.mosi_io_num = DISPLAY_MOSI_PIN;
+ buscfg.miso_io_num = GPIO_NUM_NC;
+ buscfg.sclk_io_num = DISPLAY_CLK_PIN;
+ buscfg.quadwp_io_num = GPIO_NUM_NC;
+ buscfg.quadhd_io_num = GPIO_NUM_NC;
+ buscfg.max_transfer_sz = DISPLAY_WIDTH * DISPLAY_HEIGHT * sizeof(uint16_t);
+ ESP_ERROR_CHECK(spi_bus_initialize(SPI3_HOST, &buscfg, SPI_DMA_CH_AUTO));
+ }
+
+ void InitializeLcdDisplay() {
+ esp_lcd_panel_io_handle_t panel_io = nullptr;
+ esp_lcd_panel_handle_t panel = nullptr;
+ // 液晶屏控制IO初始化
+ ESP_LOGD(TAG, "Install panel IO");
+ esp_lcd_panel_io_spi_config_t io_config = {};
+ io_config.cs_gpio_num = DISPLAY_CS_PIN;
+ io_config.dc_gpio_num = DISPLAY_DC_PIN;
+ io_config.spi_mode = 3;
+ io_config.pclk_hz = 40 * 1000 * 1000;
+ io_config.trans_queue_depth = 10;
+ io_config.lcd_cmd_bits = 8;
+ io_config.lcd_param_bits = 8;
+ ESP_ERROR_CHECK(esp_lcd_new_panel_io_spi(SPI3_HOST, &io_config, &panel_io));
+
+ // 初始化液晶屏驱动芯片
+ ESP_LOGD(TAG, "Install LCD driver");
+ esp_lcd_panel_dev_config_t panel_config = {};
+ panel_config.reset_gpio_num = DISPLAY_RST_PIN;
+ panel_config.rgb_ele_order = DISPLAY_RGB_ORDER;
+ panel_config.bits_per_pixel = 16;
+
+ ESP_ERROR_CHECK(esp_lcd_new_panel_st7789(panel_io, &panel_config, &panel));
+
+ esp_lcd_panel_reset(panel);
+
+
+ esp_lcd_panel_init(panel);
+ esp_lcd_panel_invert_color(panel, DISPLAY_INVERT_COLOR);
+ esp_lcd_panel_swap_xy(panel, DISPLAY_SWAP_XY);
+ esp_lcd_panel_mirror(panel, DISPLAY_MIRROR_X, DISPLAY_MIRROR_Y);
+
+ display_ = new SpiLcdDisplay(panel_io, panel,
+ DISPLAY_WIDTH, DISPLAY_HEIGHT, DISPLAY_OFFSET_X, DISPLAY_OFFSET_Y, DISPLAY_MIRROR_X, DISPLAY_MIRROR_Y, DISPLAY_SWAP_XY,
+ {
+ .text_font = &font_puhui_16_4,
+ .icon_font = &font_awesome_16_4,
+ .emoji_font = DISPLAY_HEIGHT >= 240 ? font_emoji_64_init() : font_emoji_32_init(),
+ });
+ }
+
+
+
+ void InitializeButtons() {
+ boot_button_.OnClick([this]() {
+ auto& app = Application::GetInstance();
+ if (app.GetDeviceState() == kDeviceStateStarting && !WifiStation::GetInstance().IsConnected()) {
+ ResetWifiConfiguration();
+ }
+ app.ToggleChatState();
+ });
+ }
+
+ // 物联网初始化，添加对 AI 可见设备
+ void InitializeIot() {
+ auto& thing_manager = iot::ThingManager::GetInstance();
+ thing_manager.AddThing(iot::CreateThing("Speaker"));
+ thing_manager.AddThing(iot::CreateThing("Lamp"));
+ if (DISPLAY_BACKLIGHT_PIN != GPIO_NUM_NC) {
+ thing_manager.AddThing(iot::CreateThing("Backlight"));
+ }
+ }
+
+public:
+ MINSI_K08_WIFI() :
+ boot_button_(BOOT_BUTTON_GPIO) {
+ InitializeSpi();
+ InitializeLcdDisplay();
+ InitializeButtons();
+ InitializeIot();
+ if (DISPLAY_BACKLIGHT_PIN != GPIO_NUM_NC) {
+ GetBacklight()->RestoreBrightness();
+ }
+
+ }
+
+ virtual Led* GetLed() override {
+ static SingleLed led(BUILTIN_LED_GPIO);
+ return &led;
+ }
+
+ virtual AudioCodec* GetAudioCodec() override {
+#ifdef AUDIO_I2S_METHOD_SIMPLEX
+ static NoAudioCodecSimplex audio_codec(AUDIO_INPUT_SAMPLE_RATE, AUDIO_OUTPUT_SAMPLE_RATE,
+ AUDIO_I2S_SPK_GPIO_BCLK, AUDIO_I2S_SPK_GPIO_LRCK, AUDIO_I2S_SPK_GPIO_DOUT, AUDIO_I2S_MIC_GPIO_SCK, AUDIO_I2S_MIC_GPIO_WS, AUDIO_I2S_MIC_GPIO_DIN);
+#else
+ static NoAudioCodecDuplex audio_codec(AUDIO_INPUT_SAMPLE_RATE, AUDIO_OUTPUT_SAMPLE_RATE,
+ AUDIO_I2S_GPIO_BCLK, AUDIO_I2S_GPIO_WS, AUDIO_I2S_GPIO_DOUT, AUDIO_I2S_GPIO_DIN);
+#endif
+ return &audio_codec;
+ }
+
+ virtual Display* GetDisplay() override {
+ return display_;
+ }
+
+ virtual Backlight* GetBacklight() override {
+ if (DISPLAY_BACKLIGHT_PIN != GPIO_NUM_NC) {
+ static PwmBacklight backlight(DISPLAY_BACKLIGHT_PIN, DISPLAY_BACKLIGHT_OUTPUT_INVERT);
+ return &backlight;
+ }
+ return nullptr;
+ }
+};
+
+DECLARE_BOARD(MINSI_K08_WIFI);
+