|
| 1 | +/* |
| 2 | + * (C) Copyright 2013 Siemens Schweiz AG |
| 3 | + * (C) Heiko Schocher, DENX Software Engineering, [email protected]. |
| 4 | + * |
| 5 | + * Based on: |
| 6 | + * U-Boot file:/include/configs/am335x_evm.h |
| 7 | + * |
| 8 | + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ |
| 9 | + * |
| 10 | + * SPDX-License-Identifier: GPL-2.0+ |
| 11 | + */ |
| 12 | + |
| 13 | +#ifndef __CONFIG_RASTABAN_H |
| 14 | +#define __CONFIG_RASTABAN_H |
| 15 | + |
| 16 | +#include "siemens-am33x-common.h" |
| 17 | + |
| 18 | +#define CONFIG_DISPLAY_CPUINFO |
| 19 | +#define CONFIG_SYS_MPUCLK 300 |
| 20 | +#define DDR_PLL_FREQ 303 |
| 21 | +#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC |
| 22 | + |
| 23 | +/* FWD Button = 27 |
| 24 | + * SRV Button = 87 */ |
| 25 | +#define BOARD_DFU_BUTTON_GPIO 27 |
| 26 | +#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ |
| 27 | +/* In dfu mode keep led1 on */ |
| 28 | +#define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ |
| 29 | + "button_dfu0=27\0" \ |
| 30 | + "button_dfu1=87\0" \ |
| 31 | + "led0=3,0,1\0" \ |
| 32 | + "led1=4,0,0\0" \ |
| 33 | + "led2=5,0,1\0" \ |
| 34 | + "led3=62,0,1\0" \ |
| 35 | + "led4=60,0,1\0" \ |
| 36 | + "led5=63,0,1\0" |
| 37 | + |
| 38 | +#undef CONFIG_DOS_PARTITION |
| 39 | +#undef CONFIG_CMD_FAT |
| 40 | + |
| 41 | +#define CONFIG_BOARD_LATE_INIT |
| 42 | + |
| 43 | + /* Physical Memory Map */ |
| 44 | +#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ |
| 45 | + |
| 46 | +/* I2C Configuration */ |
| 47 | +#define CONFIG_SYS_I2C_SPEED 100000 |
| 48 | + |
| 49 | +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 |
| 50 | +#define EEPROM_ADDR_DDR3 0x90 |
| 51 | +#define EEPROM_ADDR_CHIP 0x120 |
| 52 | + |
| 53 | +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300 |
| 54 | + |
| 55 | +#undef CONFIG_SPL_NET_SUPPORT |
| 56 | +#undef CONFIG_SPL_NET_VCI_STRING |
| 57 | +#undef CONFIG_SPL_ETH_SUPPORT |
| 58 | + |
| 59 | +#undef CONFIG_MII |
| 60 | +#undef CONFIG_PHY_GIGE |
| 61 | +#define CONFIG_PHY_SMSC |
| 62 | + |
| 63 | +#define CONFIG_FACTORYSET |
| 64 | + |
| 65 | +/* Watchdog */ |
| 66 | +#define CONFIG_OMAP_WATCHDOG |
| 67 | + |
| 68 | +/* Define own nand partitions */ |
| 69 | +#define CONFIG_ENV_OFFSET_REDUND 0x2E0000 |
| 70 | +#define CONFIG_ENV_SIZE_REDUND 0x2000 |
| 71 | +#define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE) |
| 72 | + |
| 73 | + |
| 74 | + |
| 75 | +#define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V3 |
| 76 | + |
| 77 | +#ifndef CONFIG_SPL_BUILD |
| 78 | + |
| 79 | +/* Default env settings */ |
| 80 | +#define CONFIG_EXTRA_ENV_SETTINGS \ |
| 81 | + "hostname=rastaban\0" \ |
| 82 | + "nand_img_size=0x400000\0" \ |
| 83 | + "optargs=\0" \ |
| 84 | + "preboot=draco_led 0\0" \ |
| 85 | + CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ |
| 86 | + CONFIG_ENV_SETTINGS_V2 \ |
| 87 | + CONFIG_ENV_SETTINGS_NAND_V2 |
| 88 | + |
| 89 | +#ifndef CONFIG_RESTORE_FLASH |
| 90 | +/* set to negative value for no autoboot */ |
| 91 | +#define CONFIG_BOOTDELAY 3 |
| 92 | + |
| 93 | +#define CONFIG_BOOTCOMMAND \ |
| 94 | +"if dfubutton; then " \ |
| 95 | + "run dfu_start; " \ |
| 96 | + "reset; " \ |
| 97 | +"fi;" \ |
| 98 | +"run nand_boot;" \ |
| 99 | +"run nand_boot_backup;" \ |
| 100 | +"reset;" |
| 101 | + |
| 102 | + |
| 103 | +#else |
| 104 | +#define CONFIG_BOOTDELAY 0 |
| 105 | + |
| 106 | +#define CONFIG_BOOTCOMMAND \ |
| 107 | + "setenv autoload no; " \ |
| 108 | + "dhcp; " \ |
| 109 | + "if tftp 80000000 debrick.scr; then " \ |
| 110 | + "source 80000000; " \ |
| 111 | + "fi" |
| 112 | +#endif |
| 113 | +#endif /* CONFIG_SPL_BUILD */ |
| 114 | +#endif /* ! __CONFIG_RASTABAN_H */ |
0 commit comments