feature(esp_tinyusb): Applied fix for UNPLUG event for v4.30a

Author: roma-jam

device/esp_tinyusb/include_private/tinyusb_vbus_monitor.h

@@ -29,7 +29,7 @@ typedef struct {
  * @param config VBUS monitoring configuration
  *
  * @return
- *    - ESP_ERR_INVALID_ARG if config is NULL
+ *    - ESP_ERR_INVALID_ARG if config is NULL or Timer Task Stack Depth is insufficient when MSC is enabled
  *    - ESP_ERR_INVALID_STATE if VBUS monitoring is already initialized
  *    - ESP_ERR_NO_MEM if debounce timer creation failed
  *    - ESP_OK if VBUS monitoring was initialized successfully

device/esp_tinyusb/tinyusb_vbus_monitor.c

@@ -12,18 +12,23 @@
 #include "freertos/timers.h"
 #include "driver/gpio.h"
 #include "tinyusb_vbus_monitor.h"
-<<<<<<< HEAD
-=======
 #include "tinyusb_device.h"
->>>>>>> a562322070 (refactor(esp_tinyusb): Made attached and dettached functions available as private)
 
 const static char *TAG = "VBUS mon";
 
 #if (CONFIG_IDF_TARGET_ESP32P4)
-#include "soc/usb_dwc_struct.h"
+#include "soc/usb_dwc_struct.h"         // For GOTGCTL and DCTL registers access
+#define USB_DWC_REG                     USB_DWC_HS
+
+#if (CONFIG_ESP32P4_REV_MIN_300)
+#define BVALID_OVERRIDE_SUPPORT_ENABLE  0
+#else
 // On ESP32-P4 USB OTG 2.0 signals are not wired to GPIO matrix
 // So we need to override the Bvalid signal from PHY
-#define USB_DWC_REG                     USB_DWC_HS
+#define BVALID_OVERRIDE_SUPPORT_ENABLE  1
+#endif // CONFIG_ESP32P4_REV_MIN_300
+#else
+#error "VBUS monitoring is supported only on ESP32-P4, USB OTG 2.0"
 #endif // CONFIG_IDF_TARGET_ESP32P4
 
 /**
@@ -47,6 +52,7 @@ static vbus_monitor_context_t _vbus_ctx = {
 // Additional low-level USB DWC functions, which are not present in the IDF USB DWC HAL
 //
 
+#if (BVALID_OVERRIDE_SUPPORT_ENABLE)
 // --------------- GOTGCTL register ------------------
 
 static void usb_dwc_ll_gotgctl_set_bvalid_override_value(usb_dwc_dev_t *hw, uint8_t value)
@@ -58,6 +64,7 @@ static void usb_dwc_ll_gotgctl_enable_bvalid_override(usb_dwc_dev_t *hw, bool en
 {
     hw->gotgctl_reg.bvalidoven = enable ? 1 : 0;
 }
+#endif // BVALID_OVERRIDE_SUPPORT_ENABLE
 
 // ------------------ DCTL register --------------------
 
@@ -74,7 +81,9 @@ static void usb_dwc_ll_dctl_set_soft_disconnect(usb_dwc_dev_t *hw, bool enable)
 static void vbus_appeared(void)
 {
     ESP_LOGD(TAG, "Appeared");
+#if (BVALID_OVERRIDE_SUPPORT_ENABLE)
     usb_dwc_ll_gotgctl_set_bvalid_override_value(&USB_DWC_REG, 1);
+#endif // BVALID_OVERRIDE_SUPPORT_ENABLE
     usb_dwc_ll_dctl_set_soft_disconnect(&USB_DWC_REG, false);
 }
 
@@ -84,8 +93,15 @@ static void vbus_appeared(void)
 static void vbus_disappeared(void)
 {
     ESP_LOGD(TAG, "Disappeared");
-    usb_dwc_ll_gotgctl_set_bvalid_override_value(&USB_DWC_REG, 0);
     usb_dwc_ll_dctl_set_soft_disconnect(&USB_DWC_REG, true);
+#if (BVALID_OVERRIDE_SUPPORT_ENABLE)
+    usb_dwc_ll_gotgctl_set_bvalid_override_value(&USB_DWC_REG, 0);
+#else
+    // Workaround for ESP32-P4 ECO5, USB-OTG peripheral v4.30a
+    // We are not able to detect the disconnection event from the PHY after VBUS goes low
+    // So we need to notify the upper logic about the disconnection event manually
+    tinyusb_device_detached();
+#endif // BVALID_OVERRIDE_SUPPORT_ENABLE
 }
 
 /**
@@ -153,6 +169,14 @@ esp_err_t tinyusb_vbus_monitor_init(tinyusb_vbus_monitor_config_t *config)
         return ESP_ERR_INVALID_STATE;
     }
 
+#if (CONFIG_TINYUSB_MSC_ENABLED)
+    // When MSC is enabled, timer task stack size must be sufficient to handle FS operations during detach events
+#if (configTIMER_TASK_STACK_DEPTH < 2300)
+    ESP_LOGE(TAG, "When MSC is enabled, configTIMER_TASK_STACK_DEPTH must be at least 2300 bytes to handle FS operations during attach/detach events");
+    return ESP_ERR_INVALID_ARG;
+#endif // (configTIMER_TASK_STACK_DEPTH)
+#endif // (CONFIG_TINYUSB_MSC_ENABLED)
+
     _vbus_ctx.gpio_num = config->gpio_num;
     _vbus_ctx.prev_state = false;
 
@@ -189,12 +213,15 @@ esp_err_t tinyusb_vbus_monitor_init(tinyusb_vbus_monitor_config_t *config)
     }
     // Disable GPIO interrupt
     gpio_intr_disable(_vbus_ctx.gpio_num);
+
+#if (BVALID_OVERRIDE_SUPPORT_ENABLE)
     // Set initial Bvalid override value and enable override
     usb_dwc_ll_gotgctl_set_bvalid_override_value(&USB_DWC_REG, 0);
     // Wait 1 microsecond (sufficient for >5 PHY clocks)
     esp_rom_delay_us(1);
     // Enable to override the signal from PHY
     usb_dwc_ll_gotgctl_enable_bvalid_override(&USB_DWC_REG, true);
+#endif // BVALID_OVERRIDE_SUPPORT_ENABLE
 
     // Device could be already connected, check the status and start the timer if needed
     if (gpio_get_level(_vbus_ctx.gpio_num)) {
@@ -214,7 +241,9 @@ esp_err_t tinyusb_vbus_monitor_init(tinyusb_vbus_monitor_config_t *config)
 
 timer_err:
     gpio_isr_handler_remove(_vbus_ctx.gpio_num);
+#if (BVALID_OVERRIDE_SUPPORT_ENABLE)
     usb_dwc_ll_gotgctl_enable_bvalid_override(&USB_DWC_REG, false);
+#endif // BVALID_OVERRIDE_SUPPORT_ENABLE
 isr_err:
     gpio_reset_pin(_vbus_ctx.gpio_num);
     _vbus_ctx.gpio_num = GPIO_NUM_NC;
@@ -248,8 +277,11 @@ esp_err_t tinyusb_vbus_monitor_deinit(void)
     xTimerDelete(_vbus_ctx.debounce_timer, 0);
     _vbus_ctx.debounce_timer = NULL;
 
+#if (BVALID_OVERRIDE_SUPPORT_ENABLE)
     // Disable to override the signal from PHY
     usb_dwc_ll_gotgctl_enable_bvalid_override(&USB_DWC_REG, false);
+#endif // BVALID_OVERRIDE_SUPPORT_ENABLE
+
     ESP_LOGD(TAG, "Deinit");
     return ESP_OK;
 }